About Us
   
  Products
   
  Projects
   
  Partners
   
  Downloads
   
  Contact Us
   
  Get A Quote
   
  Careers


 

 

VIDEO CONFERENCING KIOSK

Kiosk Networking

The Video Conferencing Kiosk and its Utilities

1
 Vcon Hub
2
 Software Commercial
3
 Technical Plan
4
 Hardware Specification
a)
 Mother Board
b)
 Highly Integrated Pen-III SBC
c)
 Specification Standard SBC Functions.
d)
 PCI SVGA / Flat Panel Interface
e)
 PCI Bus Ethernet Interface
f)
 Audio Functions
g)
 Solid - State Disk
h)
 Panel Link
i)
 Mechanical and Environmental
j)
 Enclosure
5
6
7
8
9
10
11
12

Specifications

Standard SBC functions

•  CPU Socket 370 for Intel Pentium-III Intel or Celeron TM Processor up to 533 MHz or Pentium III 550 MHz or above, AMD K6

•  BIOS Award 256KB Flash BIOS, supports plug & play, APM

•  Chipset Intel 440BX

•  Green function APM 1.2 compliant

•  2nd level cache 128KB/256KBon the processor

•  RAM Two 144 - pin SO DIMM sockets accept 8-128MB SDRAM

•  Enhanced IDE INTERFACE: One channel for 2IDE devices. One channel for Compact Flash TM card

•  FDD interface: supports up to two FDDs (360 KB/1.2MB/720KB/1.44MB /2.88MB)

•  Parallel port: one parallel port supports SPP/EPP/EPP/ECP mode

•  Serial ports: Four serial ports with +5V/+12V power capability (COM 1,3,4: RS-232 andCOM2 RS-232/422/485)

•  Watchdog timer: Software enabled/disabled, 63-level interval from 1 to 63 seconds. Jumper less selection generates system reset or IRQ 11

•  Keyboard/mouse connector: 8-pin header connector for keyboard and PS/2 mouse

•  USB interface: two USEB connectors with fuse protection compiles with USB spec. Rev 1.0

•  Infrared port: Supports up to 115 kbps transfer rate

•  PC/l04 expansion: 1O4-pin 16-bitPC/1O4-module connector

•  I/O bus expansion: One 32-bit PCI bus expansion slot

PCI SVGA/ Flat Panel Interface

•  Chipset: Trident Cyber 9525 DVD, high performance 64-bit GUI, 3D engine

•  Display memory: 2.5MB of SDRAM frame buffer on cyber 9525DVD, 4 MB SDRAM frame buffer on Cyber BLADE e4 TM 9540 (optional)

•  Display Type: Simultaneously supports CRT and flat panel (EL, LCD and gas plasma) displays

•  Interface: 2xAGP, Accelerator Graphics Ports 1.0 compliant

•  Display mode

•  LCD panel supports up to 800x600 @24bpp, 1024x768@24 bpp CRT displays supports up to 800x600@24bpp , 1024x768@24bpp

PCI Bus Ethernet Interface

•  Chipset: Realtek RTL8139PCI – bus Ethernet controller

•  Ethernet Interface

Audio Function

•  Chipset: ES 1989S

•  Audio Controller: AC97 ver 2.0 complaint interface, Multistream Direct Sound and Direct Sound 3D acceleration

•  Audio interface: Microphone in, Line in, CD audio inline out speaker, L, Speaker

•  MDC interface: Supports (Mobile Daughter Card) interface for optional MDC software modem.

 

Solid-state disk

•  One 50-pin socket for one Compact Flash Card, shared with one IDE channel

Panel Link (optional)

•  Chipset: Sil 154 Panel Link Digital Transmitter

•  Scalable band width: Ranging from 25~112Mhz (VGA-SXGA)

•  24/48-bit one/two pixel per clock

Mechanical and environmental

•  Power requirements: 5.2A @ 5V (4.75 to 5.25) (typical); 4.9 A @ 5V with Celeron TM 466 and 128MB SODIMM

•  Operating temperature: 0-60 degree centigrade (32~140 0 F)

Enclosure

•  Fibre Glass Reinforced Plastic

 

ISDN MODEM

The ISDN Modem OMNI, NET support PPP Multilink Protocol, allowing for communication with ISDN devices at full bandwidth of up to 128Kbps. Bandwidth allocation protocol (BACP) provides added flexibility through the PPP Multilink Protocol. Bandwidth on demanding automatically bundles two B channels with the help of BACP. Which evaluates data traffic and automatically adds and drops the second B channels needed. Call-Bamping enables users to make an analog call when two B channels are in use by dropping second B channel.

Two analog ports are also featured which allow simultaneous use of two analog devices such as telephone modem and fax machines. For Ex. User may send e-mail while talking on the phones, or the web site while sending a fax.

The Multi-Auto feature automatically detects and accepts incoming calls for PPP V.120, V.110 and X.75 freeing the users from manual protocol configuration. The Multi-Auto feature also automatically answers and identifies calls as analog or digital and routes from them accordingly.

Also DTMF and pulse dialing recognition, but in speaker, LED status indicator and multiple subscriber setting are added features. The modem is compatible with all popular operating environments like Windows 3.1, Windows 95/NT, DOS, UNIX, Macintosh, OS/2 and Novell.

 

Application and Configuration control

 

•  Flash EPROM for easy firmware upgrades

•  Diagnostic self-test and loop back

•  Zyxel ISDN AT Commands

•  Zyxel multiple stream Protocols and CAP1 1.1a and 2.0

•  Front panel switch for quick dial tear down

•  LED indicator for detailed status monitoring

Physical Characteristics

•  RJ-45 ISDN Basic Rates Interface

•  Two RJ-11Analog phone ports

•  DB-25 High speed 460.8 Kbps Serial DTE Port

 

Speed and Compatibility

•  Plug and play support for Win95/98/NT environment

•  Full compatibility with ISDN and remote PSTN via ISDN

•  112Kbps/128Kbps channel bundling: MLP, and Multilink PPP (REF1990)

•  Multiple signaling protocol compatibility with the following network switches: DSSI (for Europe), NI-1 and DMS -1OO (for USA)

•  Support X .25, V. 120, and PPP Async -to-Sync Conversation B channel Protocols

•  B-Channel speeds of 56Kbps (in- band Signaling) and 64Kbps (out-of-band Signaling)

•  High-speed 460.8Kbps DTE serial port

•  V.42b is data compression over ISDN using the X.75, V.120, and bundle protocols

•  STAC data compression using PPP/MP to provide

•  Fast downloading for video and high-quality graphics

•  Two application programs. Interfaces including ZYXEL ISDN At Commands and CAPI2.0

•  Built-in 56K modem that can communicate with other analog Modem/Fax through as ISDN line. (for omni.net LCD+Plus only)

•  Universal serial Bus (USB) interface. (For omni.net LCD Plus only)

 

VIDEO CONFERENCING (Dialup)

UV's videoconferencing Access Terminals deliver the power of large and expensive systems at a fraction of the cost .The video conferencing interface allows advanced Video over IP on our Access Terminals with support for data collaboration. Designed to maximize available bandwidth, the video conferencing system operates over an IP network at data rates up to 1.5 Mbps, and offer near-broadcast resolution at 30 frames per seconds. The Packet Assist Architecture helps eliminates network congestion while optimizing transmission quality and reliability.

UV's Videoconferencing terminal connects over LAN, ISDN, ATM, Satellite, Private Line, XDSL, Cable Modem, etc. This advanced solution for networked multimedia provides a complete set of capabilities for two way, IP-based (H.323) and ISDN (H.320) video conferencing over existing local area networks (LANs) and wide area networks (WANs).

The video conferencing interface is single solution requiring just one PCI slot. It delivers a video conferencing-advanced communication and data sharing capabilities and makes video conferencing as easy as making a phone call.

Key Features

LAN H .323 30FPS at 64 Kbps- 1.5 Mbps

ISDN H.320 128 Kbps

ISDN On-Board Single BRI

Video Frames Per Second over ISDN 30fps

Operating system NT Win 95,98

Standard Audio Output Handset

Standard Audio Input Camera or via Handset Camera

Standard Camera Fixed Focus

128K Internet Access (NDIS)

•  High-speed Web browsing

 

Additional Features

•  User-friendly conference panel and GUI

•  Camera present positions

•  PC- Phone dialer

•  Frame Grabber

•  Multiple video and audio sources

•  Pre-defined phonebook entries

•  Speed dial directory

•  Session capabilities monitor

•  Far End Camera Control (FECC) according to H.281

•  Resizable video windows up to full screen

•  Self-view video window

•  Moveable Picture-In-Picture (PIP)

•  MCU support with chair control (H.243)

•  High-speed remote access to the Internet

•  Post-Processing algorithm

•  MVIP support

•  Acoustic Echo Cancellation

Video

Video compression

H.261 (Px64)& H.263 compatible

Transmitted resolution

CIF (352x288 pixels) up to 30 frames /second

QCIF (176x144 pixels up to 30 frames/second

VGA resolution

All VGA resolution with 16/32 bits

Video input

NTSC or PAL camera with analog interface inc1ude, Secon RCA video Input

Special Features

Scalable video in a window size, picture-in-picture, self view algorithm for enhanced video quality CIF frames/sec, mute video

Camera Control

H.281 Far End Camera Control (FECC)

Audio

Audio Compression

G.711 -3.4 kHz at 56 Kbps and 48 Kbps

G.722 -3.4 kHz at 56 Kbps and 48 Kbps

G.728 -3.4 kHz at 16 Kbps

Audio I/O

Telephone handset included

Line Level output for multimedia speakers

Line level output for sound card

Automatic Gain Control (AGC)

-95dB to +95dB

Software Control led features

Volume control and mute

Acoustic Echo Cancellation (AEC) on board – 30dB ERLE@>200ms

 

 

Camera for Video Conferencing

The camera used is a desktop, which is ergonomically designed featuring the flexibly of computer mouse.

The practical Soft base unit and High base unit (optional) allows to aim the camera in every direction whether hand-held or free standing, without the difficulty of release buttons.

The camera is equipped with a variable focus lens .The focus can be adjusted manually from a distance of approximately O-cm (macro) to infinity.

A microphone is integrated into the camera to give live audio.

The output signal is CVBS according to the PAL or NTSC standard, depending on type of camera.

Focus range:

It is possible to focus on extreme short distance (approx. 0 cm) by rotating the lens in the desired direction. Sharp image can also be had within a wide range by aiming camera at an object on distance of more than 5meters and rotate the lens until sharp image is got. In this case the camera is in focus from O.6 meters till infinity.

Amplifier Card:

The Amplifier is Class B Power Amplifier operates with a DC Power Supply .It has a good input sensitivity with a negative feedback.

Working Principle of the Amplifier:

  1. The circuit work on DC Supply
  2. It uses a multi-wait Single chip and dual OP amp IC
  3. IC has a inbuilt thermal shutdown, load dump voltage surge, etc. It is rugged
  4. An external resistor sets the gain of the amplifier.
  5. Power output from the IC is taken through high value coupling capacitor to allow all AF signals easily to speakers.
  6. A capacitor is provided to avoid unwanted DC input
     

 


Copyrights © 2005 Diginue Technologies (P) Ltd. All rights reserved